Terminal units. Water terminal unit
Water-based HVAC terminal units include radiators, underfloor heating and fan coils, which are connected to water-based HVAC systems such as boilers, chillers, and air-source and ground-source heat pump units.
Radiator
The "Radiator" option lets you simulate a radiator or a group of radiators arranged within the thermal zone.
System
- Water-based heating system Select a water-based heating system defined in the "Heating and cooling systems" section or enter one directly.
Heating
- Thermal power (optional)
Specify a value for the radiator’s thermal power and for the following parameters:- Design room temperature
- Design supply temperature
- Design temperature difference
Radiant floor
The "Radiant floor" option lets you simulate the radiant floor heating system installed in the thermal zone.
System
- Water-based heating system Select a water-based heating system defined in the "Heating and cooling systems" section or to enter one directly.
Heating
- Thermal power (optional)
Specify a value for the thermal power of the underfloor heating and for the following parameters:- Design room temperature
- Design supply temperature
- Design temperature difference
Fan coil unit
The "Fan coil" terminal unit is a 4-pipe fan coil and requires connection to both cold and hot water.
The definition of a fan coil unit does not specify a rated power. Its power output depends on the flow rate and temperature of the water it receives, as well as the air flow rate it delivers.
The maximum power of the fan coil is limited by the "Maximum air flow rate", which is specified in the "Supply fan" definition panel.
System
In the "System" section, you must select one of the following systems: "Water distribution", "Air source heat pump" or "Ground source heat pump":
- Water distribution
- Water-based heating system
Select a water-based heating system defined in the "Heating and cooling systems" section or enter one directly. - Water-cooling system
Select a water-cooling system defined in the "Air-conditioning systems" section or enter one directly.
- Water-based heating system
- Aerothermal energy
- Air-source heat pump system
Select an air-source heat pump system defined in the "Air-conditioning systems" section or enter one directly.
- Air-source heat pump system
- Geothermal energy
- Geothermal heat pump: Select a geothermal heat pump defined in the "Heating and cooling systems" section or enter one directly.
Generic
The "Generic" option lets you simulate a generic fan coil unit or a group of generic fan coil units arranged within the thermal zone.
On this type of fan coil unit, the "Control" and "Supply fan" settings can be configured in the following sections:
Control
The "Control" section lets you configure the fan coil’s power control, which is achieved by adjusting the water flow rate and/or the air flow rate.
- Capacity control method (Constant air flow, variable water flow / Variable air flow, variable water flow / Intermittent air flow, constant water flow / Variable air flow, constant water flow)
- Low speed supply air flow ratio
- Medium speed supply air flow ratio
| Note: |
|---|
| The type of fan fitted to the fan coil unit is determined by the power control method, depending on the type of air flow: - Constant air flow: the fan operates at a fixed speed and is always running; consequently, it heats the air even when there is no demand. - Variable air flow: the fan is variable-speed. - Intermittent air flow: the fan has three speeds and is switched on only when there is a demand. |
Supply fan
The "Supply fan" section lets you configure the following parameters:
- Maximum air flow rate (optional)
If the fan coil’s flow rate is not specified, EnergyPlus™ calculates it automatically to meet all the zone’s loads in accordance with the zone’s "Automatic sizing options". - Specific power
- Motor efficiency
- Motor heat losses fraction in air stream
Catalogues
The "Catalogues" option lets you simulate a manufacturer’s fan coil unit installed in the thermal zone.
To do this, select whether the fan coil type is "Cassette", "Wall-mounted", "Ceiling-mounted", "Floor-mounted" or "Ducted".
The fan coil unit must then be selected from the manufacturers and models available in the Open BIM Database, which have been downloaded beforehand from the "Catalogues" option on the main interface.






